CrawlSpaceRepair.com

 Moisture Medic® is a crawl space dehumidifier and the newest generation of moisture management equipment available to the public. 70 Pint dehumidifier- HC-70Size is important because big bulky dehumidifiers may not fit into the crawl space access opening. Here the 70 pint measures 12.5" wide by 12.5" tall and 25" (cabinet only) long making it the perfect size to fit through almost any crawl space access opening. Enjoy the energy efficiency of an Energy Star rating...

Use with InstaDry® Sump Kit™ to prevent smaller drainage rock from entering the basin. For use with sandy soils and pea stone.

Use this caulk to seal the crawl space liner to the foundation in wet conditions. This premium polyurethane caulk is preferred by professional to give the best adhesion when the Foundation Seal Tape™ won't stick due to a wet foundation. This caulk is also used to fill gaps on inside corners, cracks and opening in the foundation as well as sealing the sill plate. Available in White and Grey

Sump Pump Kit - All in one This  Sump Pump Kit by InstaDry® has everything you need to help control the excess water in your crawl space. This kit comes with a 2 piece snap together basin making it the right size for every access opening. Most other options are made as a mini basin so it will fit through the opening and many still won't. That mini basin causes the pump to run shorter cycle (turn on/turn off quicker) causing more wear on the pump motor and early failure. Water slots...

This Air Support™ is used with our Moisture Medic® dehumidifiers to increase air flow in the crawl space, which makes the crawl space dehumidifier far more efficient and productive. The Air Support™ will allow the Moisture Medic® to dehumidify more area, by up to 50% more. More air flow means more dehumidifying, longer run cycles and a more efficient dehumidifier. Longer run cycles allow the dehumidifier to get to temperature and stay there while the Air Support™ continues to move the...

The basin’s new, contemporary, lightweight design will now allow you to take it in to the crawl space already assembled or in two separate pieces. The anti flow plate has now been made a part of the basin itself, and is no longer a separate piece that you have to put together. The bottom ribbed surface makes assembly fast and easy. It goes together with just a “snap”. The new basin now uses slots instead of predrilled holes for better water flow and water pressure. Whether you're a...

Foundation Seal Tape™ (FST) is used to seal the vapor barrier to the foundation wall. When installed to a completely dry & clean foundation wall, the bond is good enough to hold the vapor barrier to the wall temporarily (several hours/days) until the Foundation Pins are installed. If the foundation wall is wet in the area it will be installed and it will not bond then a polyurethane caulk must be used. This tape is 1.5" x 100' and has a reinforcement inside the tape to eliminate stretching...

This tape is used to seal the seams of the crawl space vapor barrier. It comes in  4" x 187' rolls (compare to rolls at only 108') and is white to match all of the vapor barriers we offer. This product, when installed correctly, will give you a waterproof seal at the seams. In very wet conditions it is recommended to use the Foundation Seal Tape™ under the seam to give an extra layer of protection. This tape is the perfect thickness for this application allowing proper flexibility...

The Foundation Pins™ are used to permanently secure the vapor barrier™ to the foundation wall. These pins are inserted into a 1/4" hole drilled by a hammer drill. They are to be installed every two foot, two in each corner and anywhere is cut around obstructions. These pins come in packs of 100 pieces or 1000 pieces and are required for a lasting bond to the foundation wall. The heads of our pins will not break off nor will the pin come out of the hole as with other pins on the market....

12 Mil DiamondBack This American Made crawl space liner is the basic cord reinforced vapor barrier that can be compared to most other brands on the open market for the same stated thickness, 12 Mil. Actual 12 mil is equal to .012", not 12mm. This crawl space liner does not contain any additives and is reinforced with a 1000 denier polyester cord to stablize the layers and prevent tearing. The appearance of this crawl space liner is bright white on the face and black on the back. Although it...

12 Mil Crawl Space Vapor Barrier GuardianLiner® Extremely durable, high quality crawl space vapor barrier/liner. This crawl space liner has been a favorite of the professional community since its introduction. There are three major components that make this liner an excellent choice for the crawl space environment. First, the white top layer and the tan bottom layer are made from 100% virgin polyethylene resin. This is very important because these layers will last indefinitely....

Compare the 20 Mil GuardianLiner® to CleanSpace™- Same amount of plastic and same thickness... Looking for an affordable crawl space liner in the 20 mil class? The GuardianLiner® is a vapor barrier designed to match up in appearance and performance with the CleanSpace® brand head to head. Although lengths and widths are different the barrier's formula is comparable. Both product's outer layers are made from 100% virgin polyethylene resin and reinforced with a 1000 denier polyester cord. They...